Free Model Download

Fidget Circle

A fidget toy that keeps your hands busy at your desk. It sits flat as a smooth round disc, and every way you move the stem gives it a different look — twist it and the rings spin freely with nothing to catch on, push and pull it side to side, or lift it and the 38 rings drop into a smooth cone. The stem is textured for a tactile feel, and lowering it back to the desk makes a satisfying sound.

A black print-in-place fidget circle lying flat on a tan backdrop, its 38 concentric rings stepping out from a short textured stem at the center

Downloads

Get the Files

One 3MF with the whole circle on a single plate and the tested profile saved inside, plus the same part as a plain STL for any slicer.

★
Download from Creality Cloud — it makes a real difference.

Every download through Creality Cloud earns points that help keep my models free and my pages running. If you have an account, downloading from there is the best way to support the work at no cost to you.

Download on Creality Cloud

The 3MF is the faster path — open it, say yes to the project settings and slice. A full print & play guide is attached to the Creality listing.

▤
Print & Play Guide

The same guide attached to the model listings, hosted here so you can read it before you print — PDF · 4 pages · 539 KB

Open the Guide

Ways To Play

Every Move Gives It A New Look

38 nested rings hang from one textured stem, so whatever your fingers do, the rings follow — and it all comes off the plate as one print.

A black print-in-place fidget circle lying flat on a tan backdrop, its 38 concentric rings stepping out from a short textured stem at the center
Spin It Freely
Leave it flat on the desk and twist the stem. The rings are round, so there is nothing to catch on and nothing to stop them; every ring turns all the way around and they shift against each other into mesmerizing designs. Push and pull the stem from side to side and the rings ripple off-center for a whole different set of visuals.
Fingers lifting the fidget circle by its textured stem, the 38 rings hanging below in a smooth cone
Lift It Into A Cone
Raise it by the stem and the 38 rings drop into a smooth cone. Lower it back to the desk and it makes a satisfying sound as the rings come back down. The stem is textured, so it has a tactile feel under your fingers.
The fidget circle seen from a little higher, lying flat with all 38 rings level and the textured stem standing at the center
Prints In Place
All 38 rings and the stem come off the plate already captured inside each other — nothing to glue or snap together. This is the densest of the shape set: 38 rings packed across 171 mm, and every one of them turns.

Print Settings

Slice It Right

These are the settings the circle in the photos was printed with, on a Creality Hi 1 with a 0.4 mm nozzle. The 3MF carries the full profile — open it in Creality Print or any slicer that reads 3MF projects and it is ready to go.

One color, no swaps. A single spool, no filament changes, no purge and no prime tower: 4 h 6 m and 131.58 g for the whole plate.

It prints flat, just as it rests, 170.5 mm across and 39.0 mm tall with the stem, with no supports and no brim.

Supports
None
Layer Height
0.20 mm
Walls
2
Top / Bottom
5 / 5
Infill
10% Grid
Brim
None
Material
PLA · 220 °C / 60 °C
The Part
170.5 × 170.5 × 39.0 mm · 132 g
Slice data: 170.5 by 170.5 by 39.0 mm, 4 h 6 m and 131.58 g in one color with no filament changes

More models and tested slicer settings on my Creality Cloud profile.

View Profile

Released under CC BY-NC-ND 4.0 — free for personal use, credit appreciated, no commercial use or derivatives.