Free Model Download

Fidget Pentagon

A fidget toy that keeps your hands busy at your desk. It sits flat as a five-sided plate, and every way you move the stem gives it a different look — twist it and the 22 rings sweep around into a pinwheel, push and pull it side to side, or lift it and they step down into a pyramid. The stem is textured for a tactile feel, and lowering it back to the desk makes a satisfying sound.

A black print-in-place fidget pentagon lying flat on a tan backdrop, its 22 nested five-sided rings stepping out from a short textured stem

Downloads

Get the Files

One 3MF with the whole pentagon on a single plate and the tested profile saved inside, plus the same part as a plain STL for any slicer.

★
Download from Creality Cloud — it makes a real difference.

Every download through Creality Cloud earns points that help keep my models free and my pages running. If you have an account, downloading from there is the best way to support the work at no cost to you.

Download on Creality Cloud

The 3MF is the faster path — open it, say yes to the project settings and slice. A full print & play guide is attached to the Creality listing.

▤
Print & Play Guide

The same guide attached to the model listings, hosted here so you can read it before you print — PDF · 4 pages · 478 KB

Open the Guide

Ways To Play

Every Move Gives It A New Look

22 nested rings hang from one textured stem, so whatever your fingers do, the rings follow — and it all comes off the plate as one print.

The fidget pentagon twisted flat on the desk, its 22 rings swept around out of line into a five-armed pinwheel
Twist It Into A Pinwheel
Leave it flat on the desk and twist the stem: the 22 rings sweep around into a pinwheel, every ring turning until its corners meet the ring outside it. Push and pull the stem from side to side and the rings shift off-center for a whole different set of visuals.
Fingers lifting the fidget pentagon by its textured stem, the 22 rings stepping down below into a five-sided pyramid
Lift It Into A Pyramid
Raise it by the stem and the 22 rings step down into a five-sided pyramid. Lower it back to the desk and it makes a satisfying sound as the rings come back down. The stem is textured, so it has a tactile feel under your fingers.
The fidget pentagon twisted flat on the desk, its 22 rings swept around out of line into a five-armed pinwheel
Gaps Tuned Ring By Ring
The gap between rings widens from about 1.2 mm at the stem to about 1.6 mm at the rim, so the outer rings keep turning freely instead of binding up. All 22 rings and the stem come off the plate already captured inside each other.

Print Settings

Slice It Right

These are the settings the pentagon in the photos was printed with, on a Creality Hi 2 with a 0.4 mm nozzle. The 3MF carries the full profile — open it in Creality Print or any slicer that reads 3MF projects and it is ready to go.

One color, no swaps. A single spool, no filament changes, no purge and no prime tower: 2 h 41 m and 80.84 g for the whole plate.

It prints flat, just as it rests, 169.6 x 161.3 mm and 39.0 mm tall with the stem, with no supports and no brim. It needs a 180 mm bed.

Supports
None
Layer Height
0.20 mm
Walls
2
Top / Bottom
5 / 5
Infill
10% Grid
Brim
None
Material
PLA · 220 °C / 60 °C
The Part
169.6 × 161.3 × 39.0 mm · 81 g
Slice data: 169.6 by 161.3 by 39.0 mm, 2 h 41 m and 80.84 g in one color with no filament changes

More models and tested slicer settings on my Creality Cloud profile.

View Profile

Released under CC BY-NC-ND 4.0 — free for personal use, credit appreciated, no commercial use or derivatives.