Free Model Download

Fidget Spider Web

A fidget toy that keeps your hands busy at your desk. It sits flat as a spider web, and every way you move the stem gives it a different look — twist it for mesmerizing designs, push and pull it side to side, or lift it and the 17 rings drop into a scalloped cone. The stem is textured for a tactile feel, and lowering it back to the desk makes a satisfying sound.

A white fidget spider web lying flat on a deep red backdrop, its scalloped rings ringed by black web lines, with a textured stem standing up at the center

Downloads

Get the Files

One 3MF with the whole web on a single plate, the strand color already assigned and the tested profile saved inside, plus the same part as a plain STL for any slicer.

★
Download from Creality Cloud — it makes a real difference.

Every download through Creality Cloud earns points that help keep my models free and my pages running. If you have an account, downloading from there is the best way to support the work at no cost to you.

Download on Creality Cloud

The 3MF is the faster path — open it, say yes to the project settings and slice. A full print & play guide is attached to the Creality listing.

▤
Print & Play Guide

The same guide attached to the model listings, hosted here so you can read it before you print — PDF · 4 pages · 510 KB

Open the Guide

Ways To Play

Every Move Gives It A New Look

Seventeen nested rings hang from one textured stem, so whatever your fingers do, the rings follow — and it all comes off the plate as one print.

A hand twisting the stem with the web flat on the desk, the rings swept around off-center into a new pattern
Twist And Slide
Leave it flat on the desk and twist the stem: the rings shift against each other into mesmerizing designs. Push and pull the stem from side to side and the rings ripple off-center for a whole different set of visuals.
Fingers lifting the fidget spider web by its textured stem, the rings hanging below in a scalloped cone
Lift It Into A Cone
Raise it by the stem and the 17 rings drop into a scalloped cone. Lower it back to the desk and it makes a satisfying sound as the rings come back down. The stem is textured, so it has a tactile feel under your fingers.
A white fidget spider web lying flat on a deep red backdrop, its scalloped rings ringed by black web lines, with a textured stem standing up at the center
Prints In Place
All 17 rings and the stem come off the plate already captured inside each other — nothing to glue or snap together. The gap between rings widens from the stem out to the rim, so the outer rings keep turning freely instead of binding up.

Print Settings

Slice It Right

These are the settings the web in the photos was printed with, on a Creality Hi 1 with a 0.4 mm nozzle. The 3MF carries the full profile — open it in Creality Print or any slicer that reads 3MF projects and it is ready to go.

Two colors, two filament changes. White rings with the web strands in black: 4 h for the whole plate and 97.11 g, and only 2.88 g of that is purge and prime tower. Leave room beside the web for the tower.

It prints flat, just as it rests, 178.2 × 169.5 mm across and 39.2 mm tall with the stem, with no supports and no brim.

Supports
None
Layer Height
0.20 mm
Walls
2
Top / Bottom
5 / 3
Infill
10% Gyroid
Brim
None
Material
PLA · 220 °C / 60 °C
The Part
178.2 × 169.5 × 39.2 mm · 97 g
Slice data: 178.2 by 169.5 by 39.2 mm, 4 h 0 m and 97.11 g in two colors with two filament changes

More models and tested slicer settings on my Creality Cloud profile.

View Profile

Released under CC BY-NC-ND 4.0 — free for personal use, credit appreciated, no commercial use or derivatives.