Free Model Download

Small-Part Storage

Screws, connectors, nozzles and beads end up in one jar, and finding one part means emptying it. I wanted a drawer for every kind of small part, divided the way those parts need, so I designed a four-drawer case and a full set of divider layouts to go in it.

Two black printed cases side by side with three lime green drawers pulled open, showing a two-section drawer and a nine-compartment grid

Downloads

Get the Files

A 3MF for the case and one for each of the 24 drawer layouts, every one with the tested PLA profile already set up, plus STLs of all 25 for bringing your own. The case is 152.4 × 154.6 × 155.4 mm and a drawer 145.4 × 158.5 × 34.2 mm, so both fit a 180 × 180 mm bed.

★
Download from Creality Cloud — it makes a real difference.

Every download through Creality Cloud earns points that help keep my models free and my pages running. If you have an account, downloading from there is the best way to support the work at no cost to you.

Download on Creality Cloud

The 3MFs are the faster path — open each one and slice. A full print & setup guide is attached to the Creality listing.

▤
Print & Setup Guide

The same guide attached to the model listings, hosted here so you can read it before you print — PDF · 4 pages · 1041 KB

Open the Guide

What Makes It Work

Divide It, Stack It, Mount It

Grids are named across × deep, looking at the drawer from its handle: a 2x3 is two compartments side by side and three from front to back. Mixes list their strips left to right, and each number is how many pockets that strip has from front to back. A plain number is a half-width strip, n is a narrow third and w a wide two-thirds.

Eight lime green drawers with different divider layouts laid out in front of two empty black cases
24 Divider Layouts
Uniform grids from one open bin (1x1) to sixteen compartments (4x4), plus eight mixed layouts with wide and narrow strips. Every drawer fits every slot.
Two black cases side by side holding eight closed lime green drawers
Four Drawers per Case
Each slot is 146.4 mm wide and 35 mm tall, and the 34.2 mm drawer slides in with room to spare. Pull one all the way out and carry it to the bench.
Two black cases stacked into one tower of eight closed lime green drawers
Stacks Without Hardware
Four rounded feet under each case drop into four dimples on top of the case below, so a second case sits flat and stays put.
The back wall of a lime green drawer with a raised X logo and two round recesses
Wall-Mountable
Four countersunk holes in the back take #6 or M3.5 flat-head screws, and round recesses in the back of each drawer clear a screw head that sits a little proud.

Print Settings

Slice It Right

These are the settings baked into the 3MFs, sliced with a 0.4 mm nozzle. Open them in any slicer that reads 3MF projects and they are ready to go. The case prints on its back with the openings up; each drawer prints upright, open side up.

Case 10 h 10 m and 415.45 g; each drawer 2 h 10 m to 5 h 5 m and 98 to 160 g — every layout's time and weight is on the card and in the guide.

Supports
None
Layer Height
0.20 mm
Walls
Case 2 · Drawers 3
Infill
10% gyroid
Top / Bottom
5 / 3
Brim
None
Material
PLA · 220 °C / 60 °C
Drawer Top
Concentric
Slice data: the case at 10 h 10 m and 415.45 g, and a tile for each of the 24 drawer layouts from 97.76 g to 159.63 g, 0.20 mm layers, PLA, no supports

More models and tested slicer settings on my Creality Cloud profile.

View Profile

Released under CC BY-NC-ND 4.0 — free for personal use, credit appreciated, no commercial use or derivatives.